When you order a new gate, railing or staircase, one question always comes up near the end: what finish do you want? For most steelwork in London the choice comes down to two options, powder coating or galvanising, or a mix of both. The finish decides how the metalwork looks, how long it lasts and how much upkeep it needs, so it is worth getting right.
At East London Metal Engineering Ltd we finish every job before it leaves our workshop in Forest Gate, E7. Here is how the two options compare, and how we help customers choose.
What is galvanising?
Hot-dip galvanising means dipping the finished steel into a bath of molten zinc at around 450°C. The zinc bonds with the surface of the steel and coats every face, edge, corner and the inside of hollow sections.
The big advantage is the way zinc protects steel. Even if the coating gets scratched, the zinc around the damage corrodes first and keeps the steel underneath from rusting. That is why galvanised steel can last for decades outdoors with very little maintenance.
The downside is the look. A galvanised finish is a dull silver-grey, sometimes with a crystal-like pattern, and it can be uneven in colour. It suits industrial yards, palisade fencing, fire escapes and structural steel, but many homeowners want something smarter for the front of the house.
What is powder coating?
Powder coating is a dry paint. A fine powder is sprayed onto clean, prepared metal with an electrostatic charge, so it wraps evenly around each part. The item is then baked in an oven, where the powder melts and sets into a hard, smooth finish.
Powder coating gives you colour and a clean, even look. You can choose almost any RAL colour, in matt, satin, gloss or textured finishes. It is tougher than ordinary wet paint and resists chips, scratches and fading well.
The weak point is damage. If the coating on bare steel is chipped deep enough to reach the metal, moisture can get in and rust can start to spread under the coating. On a gate that gets knocked by bins or car doors, that can happen within a few years.
The two side by side
Appearance: galvanising is plain silver-grey; powder coating comes in almost any colour and finish.
Rust protection: galvanising protects the steel even when scratched; powder coating protects well until it is chipped through.
Upkeep: galvanised steel needs very little; powder coating needs a wash now and then and quick touch-ups if it gets damaged.
Best suited to: galvanising for industrial, commercial and hidden steelwork; powder coating for gates, railings, balconies and anything on show.
The best of both: galvanising plus powder coating
For outdoor steelwork that also needs to look good, the strongest option is to do both. This is often called a duplex system. The steel is galvanised first for long-term rust protection, then powder coated in the colour you want.
If the powder coat is ever chipped, the zinc layer underneath still stops the steel from rusting. That makes a duplex finish a good choice for front gates, garden railings, external staircases and balconies, especially near busy roads, where grit and winter salt speed up corrosion.
Powder coating over galvanised steel has to be done properly. The zinc surface needs the right preparation, and the coating process has to allow for gases that can escape from the zinc during baking, which otherwise leave small pinholes in the finish. This is one reason we keep the full process under our control rather than sending work to whoever is cheapest.
Which finish is right for your job?
Front gates and driveway gates
These are on show and get knocked about, so galvanising plus powder coating is usually the best value over time. It is our usual recommendation for electric sliding gates and swing gates fitted outdoors.
Railings and balustrades
External railings in London face rain, traffic grime and the odd bike chained to them. A duplex finish is best outside. For internal stair balustrades, powder coating on its own is fine because there is little moisture.
Commercial and industrial steelwork
Palisade fencing, fire escapes, bin stores and structural steel often only need galvanising. Many commercial customers add a colour coat to match the building or meet planning requirements.
Indoor metalwork
Internal staircases, handrails, shelving frames and decorative pieces don’t face the weather, so powder coating alone usually gives the right look and durability.
Things worth knowing before you choose
Galvanising is done after fabrication. Welding galvanised steel burns off the zinc, so the item is usually made first and galvanised as a whole.
Thin sheet can distort. Very thin or large flat panels can warp in the hot zinc bath, so some designs need extra bracing or a different finish.
Hollow sections need vent holes. Box and tube sections must have small holes so the zinc can flow in and out safely. We plan these into the design so they aren’t seen.
Colour matching is easy. If you need to match existing windows, doors or railings, give us the RAL code or a sample.
Conservation areas may have rules. Some councils ask for black or specific colours on front railings, so check before choosing.
Re-coating old metalwork
Old gates and railings with flaking paint don’t always need replacing. If the steel is still sound, it can be taken down, blasted back to bare metal, then galvanised and powder coated so it looks and performs like new. If rust has eaten through the steel, replacing the damaged sections first is the better option.
Get advice on the right finish
We offer professional powder coating services for new fabrication and existing metalwork, with galvanising arranged where the job needs it. Not sure which finish suits your project? Call East London Metal Engineering Ltd on 079 5167 3924 or 020 3976 9705, or email info@eastlondonmetal.com with a few photos. We will tell you what will last, and what it will cost.
